Paslode is one of the better brands on the market, and the 902600 CF325Li is definitely a framing nailer that I knew I had to try. With the ability to drive up to 6,000 nails per charge, there are very few nailers on the market that can match this speed. Let’s see how the rest of this nailer held up during my Paslode framing nailer review.
Specifications
Weight For a heavy-duty nailer that weighs in at only 7.25 pounds, the Paslode 902600 CF325Li is impressively lightweight. There is also a rafter belt hook which I did not use, but it can definitely come in handy while on the job. Due to the grip and balance, moving and adjusting the 902600 was a breeze making the weight a non-issue. Battery Life Are you doing a job around the house and want to quickly pound some nails? This model surprised me when I could do a quick 2-minute charge and be able to drive up to 200 nails. For a job in a pinch, this is definitely a benefit that is rarely seen. If you have the time, this nailer will fully charge within just 1 hour and lasts for up to 5 hours of continuous use without a charge needed. Speed I personally cannot state that I drove 6,000 nails, but I did drive well over 1,000 in an hour making the manufacturer’s 6,000 drives in a single charge valid. For anyone doing heavy-duty work, the speed on this model is fantastic. Included Extras There are a few extras worth mentioning. You will receive a battery, a charger, safety glasses and even a carrying case. This is great for any home user that is buying a framing nailer for the first time. There is also a 5/32-inch wrench included for adjustment purposes. After over 1,000 nails driven, there was not a single jam or misfire that occurred. While I don’t know how true this would be for someone driving thousands of nails daily, this is definitely a major benefit for me. The Cons Noise. Whew – from the moment you begin nailing, you will see just how loud this nailer is. Unfortunately, higher-end nailers need immense power, and I am not sure anything can be done to lower the noise. Kids and animals alike will likely be startled upon firing up the 902600. One-Clip Compatible. Most framing nailers come with the ability to hold 2 nail clips at a time. This model only allows for one clip to be held, so you will need to swap out new nail clips more frequently. My Assessment The noise issues and one-clip are not reasons to overlook the Paslode 902600 CF325Li. Utilizing a lithium battery, this is one of the better cordless framing nailers on the market. My overall Paslode framing nailer review is positive, and I would recommend this model to friends and family.
0 Comments
Though it may seem intimidating, removing a door frame from a brick building is relatively easy. The frame is connected to the wall on either side with anchors or fasteners. These anchors are then covered with trim or casing to enhance the visual appeal of the opening. Whether your frame is made of steel or wood, you'll find that this task can be completed in just a few hours using simple tools and techniques.
Instructions Things You'll Need:
Use a hammer to drive out the hinge pins. This will allow you to remove the door from the frame, which will make it easier to remove the frame from the opening. Some exterior doors may have hinges with non-removable pins. If your door has these hinges, use a drill or screwdriver to remove the hinges from the frame entirely, then set the door aside for reuse or disposal. Cut away caulk around the perimeter of the frame using a utility knife. Repeat this process on both the interior and exterior sides of the opening, if applicable. Gently pry away trim or casing from around the door. Use the claw end of the hammer to remove this trim. Remove any remaining nails, and set the trim aside for reuse. Examine the frame. Some frames in brick walls may be butted up to the wall, while others are wrapped around. If your frame is wrapped around the wall you'll need to use a pry bar to pull the bottom of the frame away from the wall slightly. This will allow you to access the fasteners so you can remove the frame. Slide a reciprocating saw blade into the gap between the frame and the wall. Start at the bottom of the opening, and work your way up the wall, cutting away anchors or fasteners holding the frame in place. This will take longer with a wrapped frame, as you'll have to pry the frame off the wall a bit at a time as you proceed up the wall. Remove the frame from the opening by tilting the top of the unit down toward the floor once all fasteners are removed. If you are still unable to remove the frame once the fasteners are cut away, try cutting the frame at the top of each jamb where it connects to the header. This should allow you to remove the two jambs. If the header is still stuck, try repeating Step 5 to look for fasteners along the header. |