Adhesive works wonders to bind things together. Then comes a time when you want to pull them apart again, and that smudge of hardened glue is left. Although carpet glue can be stubborn, a little persistence and a little caution will remove it without damaging the underlying material. Keep the underlying material as you're collecting supplies. If it is something that would be damaged easily, be sure to purchase adhesive remover that isn't too caustic.
Instructions Citrus-based adhesive removers are often considered the safest and easiest to use, but If you are still worried about damaging the underlying material, test a small amount of the adhesive remover on it to see if it causes any damage. If it does, wash immediately with a damp rag. If the spot was left undamaged, apply adhesive remover to the hardened glue. It should cover the glue entirely so that it can do its job. Make sure to let it sit according to the manufacturer's instructions. Scrape the glue away using a plastic putty knife. Do not apply too much force or you may cause damage to the stairs. To get rid of any remaining glue residue, apply a small amount of adhesive remover to the area, let it sit for awhile and scrub the area with a damp rag. Tips & Warnings Adhesive removers tend to come in two types, liquid and paste. Use the paste style for vertical surfaces. Mineral spirits will work for some types of glue. If the glue is tan or dark brown, mineral spirits should work and will not be as likely to damage materials.
0 Comments
Crawl spaces are dark and often have poor ventilation. With the addition of moisture, they become the ideal place for mold to grow. If you have a lot of standing water in a crawl space, you will need to remove it using an immersible water pump or wet/dry shop vac before starting to fully dry the crawl space.
Drying the Crawl Space Out Use a crawl-space dehumidifier in your crawl space. Crawl-space dehumidifiers are commercial-grade and well give the best results, though you can also use a household humidifier if the problem is not too severe. Make sure not to set it or any electrical wiring in standing water or overly damp places. Clear away any debris on the crawl space floor while the dehumidifier is running. Depending on the size of your crawl space, the dehumidifier may take additional time, but it should be run for at least 24 hours. Once your crawl space is dry, install a moisture barrier on the ground. Moisture barriers are made of heavy-duty plastic and come in a variety of thicknesses. Thicker is generally better, but if budget is an issue, you don't absolutely need the highest grade of moisture barrier. Each strip of moisture barrier should run across the length of your crawl space continuously from wall to wall. Place each strip so that they overlap over the previous one just a bit, and tape them together. When you reach a wall, run the plastic about 6 inches up the wall, and tape it there. To hold the plastic in place, hammer lawn fabric stakes into the ground, through the barrier. This will not make the moisture barrier less effective, and will also create a way for any water that does get in to drain. Tips & Warnings Running a crawl space dehumidifier regularly will help keep moisture levels down. If dampness continues to be a problem, you may need to get moisture-proof installation installed along the walls of your crawl space. Paslode is one of the better brands on the market, and the 902600 CF325Li is definitely a framing nailer that I knew I had to try. With the ability to drive up to 6,000 nails per charge, there are very few nailers on the market that can match this speed. Let’s see how the rest of this nailer held up during my Paslode framing nailer review.
Specifications
Weight For a heavy-duty nailer that weighs in at only 7.25 pounds, the Paslode 902600 CF325Li is impressively lightweight. There is also a rafter belt hook which I did not use, but it can definitely come in handy while on the job. Due to the grip and balance, moving and adjusting the 902600 was a breeze making the weight a non-issue. Battery Life Are you doing a job around the house and want to quickly pound some nails? This model surprised me when I could do a quick 2-minute charge and be able to drive up to 200 nails. For a job in a pinch, this is definitely a benefit that is rarely seen. If you have the time, this nailer will fully charge within just 1 hour and lasts for up to 5 hours of continuous use without a charge needed. Speed I personally cannot state that I drove 6,000 nails, but I did drive well over 1,000 in an hour making the manufacturer’s 6,000 drives in a single charge valid. For anyone doing heavy-duty work, the speed on this model is fantastic. Included Extras There are a few extras worth mentioning. You will receive a battery, a charger, safety glasses and even a carrying case. This is great for any home user that is buying a framing nailer for the first time. There is also a 5/32-inch wrench included for adjustment purposes. After over 1,000 nails driven, there was not a single jam or misfire that occurred. While I don’t know how true this would be for someone driving thousands of nails daily, this is definitely a major benefit for me. The Cons Noise. Whew – from the moment you begin nailing, you will see just how loud this nailer is. Unfortunately, higher-end nailers need immense power, and I am not sure anything can be done to lower the noise. Kids and animals alike will likely be startled upon firing up the 902600. One-Clip Compatible. Most framing nailers come with the ability to hold 2 nail clips at a time. This model only allows for one clip to be held, so you will need to swap out new nail clips more frequently. My Assessment The noise issues and one-clip are not reasons to overlook the Paslode 902600 CF325Li. Utilizing a lithium battery, this is one of the better cordless framing nailers on the market. My overall Paslode framing nailer review is positive, and I would recommend this model to friends and family. Though it may seem intimidating, removing a door frame from a brick building is relatively easy. The frame is connected to the wall on either side with anchors or fasteners. These anchors are then covered with trim or casing to enhance the visual appeal of the opening. Whether your frame is made of steel or wood, you'll find that this task can be completed in just a few hours using simple tools and techniques.
Instructions Things You'll Need:
Use a hammer to drive out the hinge pins. This will allow you to remove the door from the frame, which will make it easier to remove the frame from the opening. Some exterior doors may have hinges with non-removable pins. If your door has these hinges, use a drill or screwdriver to remove the hinges from the frame entirely, then set the door aside for reuse or disposal. Cut away caulk around the perimeter of the frame using a utility knife. Repeat this process on both the interior and exterior sides of the opening, if applicable. Gently pry away trim or casing from around the door. Use the claw end of the hammer to remove this trim. Remove any remaining nails, and set the trim aside for reuse. Examine the frame. Some frames in brick walls may be butted up to the wall, while others are wrapped around. If your frame is wrapped around the wall you'll need to use a pry bar to pull the bottom of the frame away from the wall slightly. This will allow you to access the fasteners so you can remove the frame. Slide a reciprocating saw blade into the gap between the frame and the wall. Start at the bottom of the opening, and work your way up the wall, cutting away anchors or fasteners holding the frame in place. This will take longer with a wrapped frame, as you'll have to pry the frame off the wall a bit at a time as you proceed up the wall. Remove the frame from the opening by tilting the top of the unit down toward the floor once all fasteners are removed. If you are still unable to remove the frame once the fasteners are cut away, try cutting the frame at the top of each jamb where it connects to the header. This should allow you to remove the two jambs. If the header is still stuck, try repeating Step 5 to look for fasteners along the header. |